Search found 16 matches

by depasha
Mon Oct 19, 2015 10:19 am
Forum: Stirling and "Hot Air" Engine Forum
Topic: Gamma Stirling Engine does not working, may be fly wheel problem
Replies: 17
Views: 8392

Re: Gamma Stirling Engine does not working, may be fly wheel problem

thanks Ian SC for all of your info. Ian SC tell me what i do to increase my engine rpm.
by depasha
Wed Oct 14, 2015 4:17 am
Forum: Stirling and "Hot Air" Engine Forum
Topic: Gamma Stirling Engine does not working, may be fly wheel problem
Replies: 17
Views: 8392

Re: Gamma Stirling Engine does not working, may be fly wheel problem

thanks Ian SC for your great information in my difficult time. :big smile:
by depasha
Tue Oct 13, 2015 9:42 pm
Forum: Stirling and "Hot Air" Engine Forum
Topic: Gamma Stirling Engine does not working, may be fly wheel problem
Replies: 17
Views: 8392

Re: Gamma Stirling Engine does not working, may be fly wheel problem

thanks Ian SC for your great information provided in a difficult time. :big smile:
by depasha
Sun Oct 11, 2015 11:05 am
Forum: Stirling and "Hot Air" Engine Forum
Topic: Gamma Stirling Engine does not working, may be fly wheel problem
Replies: 17
Views: 8392

Re: Gamma Stirling Engine does not working, may be fly wheel problem

[youtube]https://www.youtube.com/watch?v=IlSSWBm31Qw[/youtube] Ian SC there is a video of my stirling engine second trial, plz observe the whole video and suggest me the solution why it is not running, currently I think after this trial that there is a over dead volume in my stirling engine design. ...
by depasha
Thu Oct 08, 2015 12:21 am
Forum: Stirling and "Hot Air" Engine Forum
Topic: Gamma Stirling Engine does not working, may be fly wheel problem
Replies: 17
Views: 8392

Re: Gamma Stirling Engine does not working, may be fly wheel problem

thanks Ian SC Ian SC I had seen in stirling engine sites in which some people use counter weight clamp on flywheel 90degree leading to the displacer pin and other doesn't use the counter weight but both engines are working. so Ian SC suggest me that I use counter weight on my engine or not. plz chec...
by depasha
Mon Oct 05, 2015 4:41 am
Forum: Stirling and "Hot Air" Engine Forum
Topic: Gamma Stirling Engine does not working, may be fly wheel problem
Replies: 17
Views: 8392

Re: Gamma Stirling Engine does not working, may be fly wheel problem

thanks a lot Ian SC Ian SC when starting the engine how much time required to heat the hot side of engine to produce enough pressure inside the engine. Can you suggest me that I install a pressure guage at the back side of plates to check the inside pressure if ok so what capacity of pressure guage ...
by depasha
Sun Oct 04, 2015 8:54 am
Forum: Stirling and "Hot Air" Engine Forum
Topic: Gamma Stirling Engine does not working, may be fly wheel problem
Replies: 17
Views: 8392

Re: RE: Re: Gamma Stirling Engine does not working, may be fly wheel problem

Thanks Ian Sc Ian SC I modified my engine flywheel in which I increase weight at its circumference you can see in pics. After that this modified flywheel make four revolution when I rotate by hand. So tell me this flywheel is ok or not. Ian SC a question with you that what kind of heating source th...
by depasha
Sun Oct 04, 2015 8:43 am
Forum: Stirling and "Hot Air" Engine Forum
Topic: Gamma Stirling Engine does not working, may be fly wheel problem
Replies: 17
Views: 8392

Re: Gamma Stirling Engine does not working, may be fly wheel problem

Thanks Ian Sc Ian SC I modified my engine flywheel in which I increase weight at its circumference you can see in pics. After that this modified flywheel make four revolution when I rotate by hand. So tell me this flywheel is ok or not. Ian SC a question with you that what kind of heating source tha...
by depasha
Sat Oct 03, 2015 1:11 pm
Forum: Stirling and "Hot Air" Engine Forum
Topic: Gamma Stirling Engine does not working, may be fly wheel problem
Replies: 17
Views: 8392

Re: Gamma Stirling Engine does not working, may be fly wheel problem

Thanks Ian SC
dear Ian SC tell me about what positions is required for piston and displacer when start the engine and also tell me when I placed piston at top dead center it creates pressure during rotating the flywheel so what minimum pressure is required.
by depasha
Sat Oct 03, 2015 1:39 am
Forum: Stirling and "Hot Air" Engine Forum
Topic: Gamma Stirling Engine does not working, may be fly wheel problem
Replies: 17
Views: 8392

Gamma Stirling Engine does not working, may be fly wheel problem

Please any one suggest me that how to calculate the weight of fly wheel , My flywheel gives only 1 rev. Is it enough or not? How many revolutions may the engine have minimum required to start. Also give me the suggestion about the minimum weight of flywheel. I have the fly wheel of weight 1.3 Kg , D...
by depasha
Fri Sep 13, 2013 1:17 am
Forum: Stirling and "Hot Air" Engine Forum
Topic: Area for air passage b/t displacer cylinder and powerpiston
Replies: 11
Views: 6624

Area for air passage b/t displacer cylinder and powerpiston

hi Ian tell me about what the area required for the passage of air move between the powerpiston cylinder and displacer cylinder my engine parameters are displacer cylinder dia=61mm piston cylinder dia =42mm my some experiance is that if area of passage of air is small so the powerpiston move to and ...
by depasha
Thu Sep 12, 2013 3:37 am
Forum: Stirling and "Hot Air" Engine Forum
Topic: Ratio b/t displacer and power piston
Replies: 16
Views: 11922

Re: Ratio b/t displacer and power piston

hi Ian tell me about what the area required for the passage of air move between the powerpiston cylinder and displacer cylinder my engine parameters are displacer cylinder dia=61mm piston cylinder dia =42mm my some experiance is that if area of passage of air is small so the powerpiston move to and ...
by depasha
Sat Sep 07, 2013 3:29 am
Forum: Stirling and "Hot Air" Engine Forum
Topic: Ratio b/t displacer and power piston
Replies: 16
Views: 11922

Re: Ratio b/t displacer and power piston

hi Ian sc
tell me about some parameter about engine when we calculate the ratio of powerpiston and displacer so either diameter of displacer or bore of displacer cylinder take into calculation.
thanks in advance.