Robinson Hot Air Engine

Discussion on Stirling or "hot air" engines (all types)
Post Reply
Trevor
Posts: 203
Joined: Sun Nov 06, 2016 4:07 am

Robinson Hot Air Engine

Post by Trevor » Wed Jun 12, 2019 3:24 am

HI all
I am in the process of making a Robinson Sterling engine with a piston diameter of 39mm and a stroke of 34mm giving me a 40.6CC volume.
My displacer cylinder is 69mm internal diameter (stainless Steel). With a ratio of approx 1.6:1 the displacer cylinder has a stroke of 18mm which isn't much and I am restricted to this sizing.
So! What I need help with is can I make a longer displacer cylinder and displacer piston with such a small stroke of the displacer piston without losing the the normal 1/3rd - 2/3rd recommended ratio. Will the longer displacer I am thinking of using cause to much heat loss when the displacer piston is too long.
Trev

Ian S C
Posts: 2213
Joined: Thu Dec 02, 2010 5:15 am
Location: New Zealand

Re: Robinson Hot Air Engine

Post by Ian S C » Thu Jun 13, 2019 2:46 am

With the Robinson the displacer is short and fat, and in full size has an internal regenerator. At a glance I would say that you are going in the right direction.

Here's a photo of a mates Robinson a the local A&P Show the day after it arrived in New Zealand from Australia.

Ian S C

Image

Image
DSC00730 (640x480).jpg
DSC00730 (640x480).jpg (278.24 KiB) Viewed 135 times
Attachments
DSC00729 (640x480).jpg
DSC00729 (640x480).jpg (254.96 KiB) Viewed 135 times

Trevor
Posts: 203
Joined: Sun Nov 06, 2016 4:07 am

Re: Robinson Hot Air Engine

Post by Trevor » Thu Jun 13, 2019 5:13 am

Thanks Ian.
Nice looking engines and I hope mine will look something of the same. I used a small milling machine from a neighbour to make a water channel through the top section and I might as well make a small water cooler on the bottom as well.
After a lot of thought, I will go with an internal regenerator made from stainless kitchen scourers.
I have managed to finish the drive network and now comes the hard part.
Thanks again - Trev

Ian S C
Posts: 2213
Joined: Thu Dec 02, 2010 5:15 am
Location: New Zealand

Re: Robinson Hot Air Engine

Post by Ian S C » Fri Jun 14, 2019 5:50 am

Qn the full size motor the vertical rectangle between the crank and the flywheel is the water tank. The piston on the motor in the photo is 10" dia, and the axe is to chop the wood for the fire, the owner didn't have any fire wood at home, so he got some bags of fire wood at the petrol station on his way to the show.

Trevor
Posts: 203
Joined: Sun Nov 06, 2016 4:07 am

Re: Robinson Hot Air Engine

Post by Trevor » Sat Jun 15, 2019 2:19 am

Pretty awesome. Certainly would be nice to have one of those.
I made up the displacer and the regenerator and finally got it all together today. I ended up with a 20mm depth displacer and a 20mm stroke.
Fired it up and away she went. Pretty good watching the linkage work. I will set up some pics after I have painted it and made a fire box for it.
Trev

Ian S C
Posts: 2213
Joined: Thu Dec 02, 2010 5:15 am
Location: New Zealand

Re: Robinson Hot Air Engine

Post by Ian S C » Sun Jun 16, 2019 3:08 am

Trev, it's a good feeling when you get a motor that you built your self going.

I build my motors to be developed, so I don't do much painting, usually just the flywheel. Have known people that have got their motor going, then stripped it down and painted it, then had trouble getting it going again.
Ian S C

Trevor
Posts: 203
Joined: Sun Nov 06, 2016 4:07 am

Re: Robinson Hot Air Engine

Post by Trevor » Sun Jun 16, 2019 5:15 pm

Know that feeling Ian (hee hee). Here are some pictures of the finished parts I did. I still need to finish the meths burner and fire box proper.
Had to borrow a milling machine from my mate to make water channels in the main block and then screw on a top plate, Whew!!! That was a chore and many screws.
My engines go on display at the Cairns Show with my cousin Ted who has steam engines - Makes for quite a display when they are all running.
I very rarely make any changes to them except maybe to pretty them up. Love your work though Ian.
Trev

Trevor
Posts: 203
Joined: Sun Nov 06, 2016 4:07 am

Re: Robinson Hot Air Engine

Post by Trevor » Sun Jun 16, 2019 5:17 pm

The Pictures as finished articles
Trev
Attachments
Picture9.jpg
Picture9.jpg (48.08 KiB) Viewed 76 times
Picture8.jpg
Picture8.jpg (48.67 KiB) Viewed 76 times
Picture7.jpg
Picture7.jpg (46.96 KiB) Viewed 76 times
Picture6.jpg
Picture6.jpg (45.5 KiB) Viewed 76 times
Picture5.jpg
Picture5.jpg (45.59 KiB) Viewed 76 times
Picture4.jpg
Picture4.jpg (38.82 KiB) Viewed 76 times
Picture2.jpg
Picture2.jpg (37.27 KiB) Viewed 76 times
Picture1.jpg
Picture1.jpg (50.02 KiB) Viewed 76 times

Ian S C
Posts: 2213
Joined: Thu Dec 02, 2010 5:15 am
Location: New Zealand

Re: Robinson Hot Air Engine

Post by Ian S C » Mon Jun 17, 2019 5:57 am

It seems that there are a few 'model engineers" in the Cairns area, there is a couple on the Model Engineer web site, Hopper, and Brian, the former an experienced modeler, and the latter a newby.

My second motor used a sewing machine wheel for many years until I needed it for another motor, so I made a new one for the old machine, a bit heavier which helped a bit with the power, the motor will actually work at high speed and virtually no torque with no flywheel at all, but set up right it can make it to 5 Watts. That motor is based on Dyna by James G. Rizzo in vol 1 of the "Stirling Engine Manual".

Ian S C

Image

Image
Test 002 (640x480).jpg
Test 002 (640x480).jpg (198.55 KiB) Viewed 66 times
Attachments
Test 005 (640x480).jpg
Test 005 (640x480).jpg (249.99 KiB) Viewed 67 times

Trevor
Posts: 203
Joined: Sun Nov 06, 2016 4:07 am

Re: Robinson Hot Air Engine

Post by Trevor » Mon Jun 17, 2019 2:33 pm

That's quite a beautiful engine you have made Ian and I do like the radiator. I have just recently brought a computer radiator which suits a small fan and I will be looking forward to using it on a small power house like the one you have built.
I must try and contact the two modelers you have mentioned. You seem to be pretty good with your memory, mines shot (heehee).
Thanks Ian
Trev

Post Reply