Page 1 of 2

Engine vacuum

Posted: Sat Nov 05, 2016 7:31 pm
by thanh-cuibap
I'm going to do the engine vacuum ... but there is so little information about it, everyone can give me drawings, information.., I can do the cylinder, piston aluminum ??

Re: Engine vacuum

Posted: Sun Nov 06, 2016 2:27 am
by Ian S C
What do you mean by "the engine vacuum", do you mean that you are going to build a "flame licker". If so the best metal would be cast iron in a stainless steel cylinder.
Ian S C

Re: Engine vacuum

Posted: Sun Nov 06, 2016 3:24 am
by thanh-cuibap
I'M SORRY !! YES ..I'm going to do the flame licker !! I want to make the cylinder and piston aluminum so tractable and research .. then will do better ..I can do the cylinder, piston aluminum ?? there is so little information about it, everyone can give me drawings, information..you can guide me somethings ....

Re: Engine vacuum

Posted: Mon Nov 07, 2016 1:51 am
by Ian S C
Aluminium has a number of difficulties, first is the high coefficient of friction. Next it has a high rate of expansion, so to fit a hot cylinder, it needs to be made with a large clearance when it is cold.
Yes it's nice and easy to machine, and easy to obtain, but the cast iron in a stainless cylinder is more correct engineering.
Ian S C

Re: Engine vacuum

Posted: Mon Nov 07, 2016 2:52 am
by thanh-cuibap
thanks Ian !!

Re: Engine vacuum

Posted: Fri Nov 11, 2016 12:09 am
by Trevor
Hi Ian. I too am going to make a flame flicker and was thinking of using aluminium as the cylinder, however, I see this should not be the case.
Can you use steel for the cylinder and use aluminium for the piston? It is hard to get cast iron here in Atherton or anywhere close here.
Trevor

Re: Engine vacuum

Posted: Fri Nov 11, 2016 3:19 am
by Ian S C
Atherton, Australia? Yes I understand that, know a bloke in Cairnes with similar problems, got to send over seas for bits, quicker than from down south.
You might be better off with brass if you can get it. Aluminium doesn't work the best rubbing against anything, bit of a bl**%$ nuisance.
Ian S C

Re: Engine vacuum

Posted: Fri Nov 11, 2016 4:58 am
by Trevor
Thanks for that Ian. Yep just out of Cairns but a long way from NZ.
Brass is a product that I still can get. Thanks for putting me onto the right stuff as I have had a lot of problems using aluminium.
Trevor

Re: Engine vacuum

Posted: Sat Nov 12, 2016 7:35 pm
by thanh-cuibap
thanks Trevor and Ian !!

Re: Engine vacuum

Posted: Mon Nov 14, 2016 2:39 am
by Ian S C
My+Pictures.jpg
My+Pictures.jpg (77.92 KiB) Viewed 9092 times
This is a much used flame licker, that I built about twenty years ago from a diagram in an old "Model Engineer" magazine. Ian S C
[img]
DSC01027 (640x480).jpg
DSC01027 (640x480).jpg (105.29 KiB) Viewed 9092 times
DSC01027 (640x480).jpg
DSC01027 (640x480).jpg (105.29 KiB) Viewed 9092 times
[/img]

Re: Engine vacuum

Posted: Mon Nov 14, 2016 2:53 am
by thanh-cuibap
thank Ian !!

Re: Engine vacuum

Posted: Sun Nov 20, 2016 9:04 pm
by thanh-cuibap
information to people about the flame licker engine !
http://ridders.nu/Webpaginas/pagina_erv ... ameset.htm

Re: Engine vacuum

Posted: Mon Nov 21, 2016 1:39 am
by Ian S C
I have built one of Jan's flame lickers, I haven't got it going yet, might have to try again.
Ian S C

Re: Engine vacuum

Posted: Thu May 25, 2017 4:36 am
by thanh-cuibap
Ian S C wrote:
My+Pictures.jpg
This is a much used flame licker, that I built about twenty years ago from a diagram in an old "Model Engineer" magazine. Ian S C
[img]
DSC01027%20(640x480).jpg
DSC01027%20(640x480).jpg
[/img]
Hi Ian !! Can you tell me diameter bore cylinder of your flame eater ??

Re: Engine vacuum

Posted: Fri May 26, 2017 3:46 am
by Ian S C
One inch bore. I took all measurements from the scale on the drawing.
Ian S C